氣動薄膜調節閥對工業生產的影響非常大，如果真的是想要保證好后續的工作不受到影響，調節閥的使用還是非常重要，一旦出現問題，都有可能會導致整體設備的故障。而且現在基本上執行器、設備開關門等都是需要使用到調節閥，所以必須要定期對設備進行檢查，一旦出現問題及時調整才是更為重要的。但是如果這類調節閥出現不動作的情況，應該如何來進行處理呢?

Pneumatic diaphragm control valves have a significant impact on industrial production. If you really want to ensure that subsequent work is not affected, the use of control valves is still very important. Once problems occur, it may lead to overall equipment failure. Moreover, nowadays, actuators, equipment opening and closing doors, etc. all require the use of regulating valves, so it is necessary to regularly inspect the equipment and make timely adjustments in case of problems. But if this type of regulating valve fails to operate, how should it be handled?

檢查好氣源壓力的情況

Check the pressure of the air source

正常使用氣動薄膜調節閥，那么肯定還是應該做好氣源壓力方面的檢查，這樣才能夠讓我們知道具體的故障情況到底如何。多數情況下調節閥都是質量比較不錯的，如果真的是想要保證很好的使用效果，就應該定期進行氣源故障方面的檢查。如果真的是氣源沒有問題，再去進行其他方面的檢查，這樣恢復好調節閥的使用自然也是要更加容易一些，大家還是可以放心。

If using a pneumatic diaphragm control valve normally, it is definitely necessary to check the pressure of the air source in order to let us know the specific fault situation. In most cases, regulating valves are of good quality. If you really want to ensure good performance, you should regularly check for air source faults. If there is really no problem with the air source, then go for other inspections. This way, it will be easier to restore the use of the regulating valve, and everyone can still rest assured.

進行定位器等設備檢查

Conduct equipment inspections such as locators

如果本身氣源原來就是正常的，經過測試沒有太大的問題，那么肯定還是需要進行定位器或者是電器轉換器等方面的檢查，看一下是否有輸出。氣動薄膜調節閥盡可能還是要先將其放大，確定好是否有輸出才行，如果沒有輸出，那么就進行放大器恒節流孔的檢查，確實是否有堵塞等。建議還是應該做好整體上的環節檢查，每一個設備內部都進行檢查，自然也可以讓我們放心。

If the original air source is normal and there are no major problems after testing, then it is definitely necessary to check the locator or electrical converter to see if there is output. As much as possible, the pneumatic diaphragm control valve should be enlarged first to determine whether there is output. If there is no output, then check the constant throttle hole of the amplifier to see if there is any blockage. It is recommended to conduct a comprehensive inspection of the entire process, and inspect the interior of each device, which can naturally give us peace of mind.